Dyson CSYS 4K Desk (Black) Let's get your machine working.

Please check the following:

Is the power cord or plug damaged?

Check other household appliances.

Check the light in another socket.

Carefully turn the light on its side.

Ensure the power cord is plugged into the centre of the base.

Carefully lay the cord through the indicated groove ensuring it does not become twisted.

Place the light upright ensuring cord remains in the slot.

Ensure the light is plugged into a wall socket and switched on.

Check the dimmer switch

Press the power button to switch on.

Hold the switch down to use the dimmer switch.

Check wheel carriage plates

Check that the wheel carriage plates are screwed together currently.

Follow the procedure image for correct assembly.

Disconnect the carriage plates

Ensure the following before starting the checks.

Ensure the light is at the top before carrying out the checks. Failure to do this will cause the weight to drop.

Use Hex key provided to remove the three screws.

Be careful to capture all screws when they are loosened.

Hold the heat sink at all times when removing from the upright.

Ensure the red tape on the plates covering the contacts has been removed.

Press the two parts together with one hand.

Loosely screw in the three screws.

Recheck alignment.

Proceed to screw until securely clamped.

Unplug the light and leave for 5 minutes.

Plug the light in and switch on.

Check wheel carriage plates

Check that the wheel carriage plates are screwed together currently.

Disconnect the carriage plates

Follow the procedure image for correct assembly.

Ensure the following before starting the checks.

Ensure the light is at the top before carrying out the checks. Failure to do this will cause the weight to drop.

Use Hex key provided to remove the three screws.

Be careful to capture all screws when they are loosened.

Hold the heat sink at all times when removing from the upright.

Ensure the red tape on the plates covering the contacts has been removed.

Reassemble the carriage plates

Loosely screw in the three screws.

Recheck alignment.

Proceed to screw until securely clamped.

Check electrical supply

Please check the following:

Is the power cord or plug damaged?

Check other household appliances.

Check the light in another socket.

Check power cord

Carefully turn the light on its side.

Ensure the power cord is plugged into the center of the base.

Carefully lay the cord through the indicated groove ensuring it does not become twisted.

Place the light upright ensuring the cord remains in the slot.

Ensure the light is plugged into a wall socket and switched on.

Check the dimmer switch

Press the power button to switch on.

Hold the switch down to use the dimmer switch.

Check wheel carriage plates

Check that the wheel carriage plates are screwed together currently.

Follow the procedure image for correct assembly.

Disconnect the carriage plates

Ensure the following before starting the checks.

Ensure the light is at the top before carrying out the checks. Failure to do this will cause the weight to drop.

Use Hex key provided to remove the three screws.

Be careful to capture all screws when they are loosened.

Hold the heat sink at all times when removing from the upright.

Ensure the red tape on the plates covering the contacts has been removed.

Reassemble the carriage plates

Press the two parts together with one hand.

Loosely screw in the three screws.

Recheck alignment.

Proceed to screw until securely clamped.

Please open the PDF for the user guide.

How to assemble your Dyson light

Stand the light on a flat surface.

Place the light upright ensuring the cord remains in the slot.

Remove the red tape from the mounting plates to expose the electrical contacts.

Align the square shapes and screw holes on the heat sink arm and the upright.

Press the two parts together with one hand.

Loosely screw in the three screws.

Recheck alignment.

Proceed to screw until securely clamped.

Remove packaging and tape

Remove the packaging on the base.

Remove the red tape on detachable arm.

Remove transparent tape on upright.

Plug the power cord into the centre of the base.

Carefully lay the cord through the indicated groove ensuring it does not become twisted.

Using the dimmer

Press the power button to switch on.

Hold the switch down to use the dimmer switch.

How to reposition the Dyson light

The LED head can be positioned directionally in 3 axes.

Only use the heat sink arm to reposition.