On the side of the Direct drive cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.
Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit the Brush bar back into the cleaner head and securely fasten the end cap.
Place the Cleaner head onto the Wand and test the machine.
We're glad the problem's been solved.
Please let us know if there's anything else we can help you with.
To ensure the correct checks are carried out, we will need to determine if this is a pick up issue or if the machine is pulsating. We can check this by seeing what light shows on the machine.
Press and hold the trigger for 10 seconds.
Please ensure the bin is empty before continuing with any checks.
Remove all tools and accessories from the machine e.g. Wand, Cleaner head, Crevice tool etc.
Press and hold the trigger for 10 seconds.
Check both ends of the Wand for blockages and remove as necessary.
Refit the Cleaner head onto the Wand and connect the Wand back onto the machine.
On the side of the Direct drive cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.
Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.
Place the Cleaner head onto the bin and test the machine.
We're glad the problem's been solved.
Please let us know if there's anything else we can help you with.
Check the inlet at the front of the machine for any blockages and remove as necessary.
Push the bin release catch underneath the bin to release the bin base. Check the opening on the cyclone shroud for any blockages. Re-attach the bin and close the base.
Press and hold the trigger for 10 seconds.
Push the bin release catch underneath the bin to release the base. Press the button located on the bin runner to release the bin and slide it off the runner.
Gently tap the side of the cyclone over a bin. This will remove any fine dust clogged up in the cyclone.
Refit the bin back on to the machine and test the machine.
WARNING: Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave, or near a naked flame.
This indicates the filter needs washing. Please follow the steps in the video.
Ensure the filter is completely dry before refitting. Press the trigger and run the machine for 2 minutes and then check the filter light.
You might need a replacement part.
It looks like the Filter is not working. You can solve this by ordering a new one below.
Filter
Part no. 969082-01
Replacement filter for your Dyson vacuum cleaner.
$43.99
Filter
Part no. 969082-01
Replacement filter for your Dyson vacuum cleaner.
$43.99
$43.99
Remove the filter by twisting anticlockwise to the open position and gently pull away. Remove any excess debris from the filter prior to washing.
Wash the inside of the filter first; hold it upright under the cold tap and agitate using a rotation motion.
Wash the outside of the filter; fill it with cold water, place your hand over the open end and shake gently.
Repeat washing the inside and outside of the filter until the water runs clear.
Gently tap the filter to remove any excess water.
Leave the filter to dry with the open end facing up for as long as possible.
Ensure the filter is completely touch dry prior to refitting.
WARNING: Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave, or near a naked flame.
To refit, return the filter to the open position and twist clockwise until it clicks into place.
On the side of the Cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.
Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit the Brush bar back into the cleaner head and securely fasten the end cap.
Place the Cleaner head onto the Wand and test the machine.
Under the Cleaner head by the Soft roller, locate the fastener. Using a coin, turn the fastener anticlockwise a quarter of the way to unlock the end cap, and slide it up to remove.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit the Brush bar back into the cleaner head and securely fasten the end cap.
Place the Cleaner head onto the Wand and test the machine.
Check the inlet at the front of the machine for any blockages and remove as necessary.
Push the bin release catch underneath the bin to release the bin base. Check the opening on the cyclone shroud for any blockages. Re-attach the bin and close the base.
Press and hold the trigger for 10 seconds.
This indicates the filter needs washing. Please follow the steps in the video.
Ensure the filter is completely dry before refitting. Press the trigger and run the machine for 2 minutes and then check the filter light.
Please ensure the bin is empty before continuing with any checks.
Remove all tools and accessories from the machine e.g. Wand, Cleaner head, Crevice tool etc.
Press and hold the trigger for 10 seconds.
Check both ends of the Wand for blockages and remove as necessary.
Refit the Cleaner head onto the Wand and connect the Wand back onto the machine.
With the accessory removed from the machine, check both ends for blockages and remove as necessary.
Refit the accessory back onto the machine.
Press and hold the trigger for 10 seconds.
Check the inlet at the front of the machine for any blockages and remove as necessary.
Push the bin release catch underneath the bin to release the bin base. Check the opening on the cyclone shroud for any blockages. Re-attach the bin and close the base.
Press and hold the trigger for 10 seconds.
Remove all tools and accessories from the machine.
Put the machine in MAX power mode.
Press and hold the trigger for 10 seconds.
Check both ends of the Wand for blockages and remove as necessary.
Refit the Cleaner head onto the Wand and connect the Wand back onto the machine.
Press and hold the trigger for 10 seconds.
If the noise is still present, select the floor tool you have been using.
On the side of the Direct drive cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.
Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.
Place the Cleaner head onto the bin and test the machine.
Apologies. We can’t help you online.
But our Customer Support Team will be able to solve your problem.
Call us on 1-877-397-6622
We're glad the problem's been solved.
Please let us know if there's anything else we can help you with.
On the side of the Cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.
Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.
Place the Cleaner head onto the bin and test the machine.
Apologies. We can’t help you online.
But our Customer Support Team will be able to solve your problem.
Call us on 1-877-397-6622
Under the Cleaner head by the Soft roller, locate the fastener. Using a coin, turn the fastener anticlockwise a quarter of the way to unlock the end cap, and slide it up to remove.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.
Place the Cleaner head onto the bin and test the machine.
You might need a replacement part.
It looks like the Mini motorized tool is not working. You can solve this by ordering a new one below.
Mini motorized tool
Part no. 967479-05
Replacement quick-release mini motorized tool for your Dyson vacuum cleaner.
$83.99
Mini motorized tool
Part no. 967479-05
Replacement quick-release mini motorized tool for your Dyson vacuum cleaner.
$83.99
Push the bin release catch underneath the bin to release the base. Press the button located on the bin runner to release the bin and slide it off the runner.
Press and hold the trigger for 10 seconds.
Apologies. We can't help you online.
But our Customer Support Team will be able to solve your problem. Call us on 1-877-397-6622
Check the inlet at the front of the machine for any blockages and remove as necessary.
Attach the bin to the machine by sliding it back on.
Once attached, push the bin fully on to the machine and close the bin base.
Press and hold the trigger for 10 seconds.
Apologies. We can’t help you online.
But our Customer Support Team will be able to solve your problem.
Call us on 1-877-397-6622
The blockage light usually appears when the machine is pulsating. The blockage light is located by the power pack.
If the machine is not performing as well as it used to this is typically caused by a partial or full blockage within the openings of the machine.
Please remove the floor tool from the machine and check the Wand for blockages.
With the accessory removed from the machine, check both ends for blockages and remove as necessary.
Refit the accessory back onto the machine.
Press and hold the trigger for 10 seconds.
Check the inlet at the front of the machine for any blockages and remove as necessary.
Push the bin release catch underneath the bin to release the bin base. Check the opening on the cyclone shroud for any blockages. Re-attach the bin and close the base.
Press and hold the trigger for 10 seconds.
Push the bin release catch underneath the bin to release the base. Press the button located on the bin runner to release the bin and slide it off the runner.
Gently tap the side of the cyclone over a bin. This will remove any fine dust clogged up in the cyclone.
Refit the bin back on to the machine, attach the wand and cleaner head and test the machine.
This indicates the filter needs washing. Please follow the steps in the video.
Ensure the filter is completely dry before refitting. Press the trigger and run the machine for 2 minutes and then check the filter light.
Wash the inside of the filter first; hold it upright under the cold tap and agitate using a rotation motion.
Wash the outside of the filter; fill it with cold water, place your hand over the open end and shake gently.
Repeat washing the inside and outside of the filter until the water runs clear.
Gently tap the filter to remove any excess water.
Leave the filter to dry with the open end facing up for as long as possible.
Ensure the filter is completely touch dry prior to refitting.
WARNING: Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave, or near a naked flame.
To refit, return the filter to the open position and twist clockwise until it clicks into place.
Apologies. We can't help you online.
But our Customer Support Team will be able to solve your problem. Call us on 1-877-397-6622
On the side of the Direct drive cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.
Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit the Brush bar back into the cleaner head and securely fasten the end cap.
Place the Cleaner head onto the Wand and test the machine.
On the side of the Mini motorised head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.
Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit the Brush bar back into the cleaner head and securely fasten the end cap.
Place the Cleaner head onto the Wand and test the machine.
Under the Cleaner head by the Soft roller, locate the fastener. Using a coin, turn the fastener anticlockwise a quarter of the way to unlock the end cap, and slide it up to remove.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit the Brush bar back into the cleaner head and securely fasten the end cap.
Place the Cleaner head onto the Wand and test the machine.
The machine is designed to pulsate. This is an audible feature that indicates a problem, as well as preventing damage to the motor. This is usually caused by a restriction in airflow or a blockage within the machine.
If the machine does not have any power, please check the status light and select which light is showing.
Make sure the machine is unplugged from the charger and check the status light.
The filter indicator will flash intermittently when the filter unit is not fitted correctly.
To refit, return the filter unit to the open position and twist clockwise until it clicks into place.
Place the machine on charge.
If one, two or three blue lights appear whilst the machine is plugged in, this suggests it is on charge.
Apologies. We can’t help you online.
But our Customer Support Team will be able to solve your problem.
Call us on 1-877-397-6622
You might need a replacement part.
It looks like the Charger is not working. You can solve this by ordering a new one below.
Charger
Part no. 969350-02
<p>Charges your vacuum with or without the Docking station</p>
$32.99
Charger
Part no. 969350-02
<p>Charges your vacuum with or without the Docking station</p>
$32.99
This indicates the machine needs charging. Place the machine on charge for 3.5 hours.
If the lights now flash red and blue, please follow the appropriate step.
Apologies. We can’t help you online.
But our Customer Support Team will be able to solve your problem.
Call us on 1-877-397-6622
Apologies. We can’t help you online.
But our Customer Support Team will be able to solve your problem.
Call us on 1-877-397-6622
This indicates the machine needs charging. Place the machine on charge for 3.5 hours.
If the lights now flash red and blue, please follow the appropriate step.
Apologies. We can’t help you online.
But our Customer Support Team will be able to solve your problem.
Call us on 1-877-397-6622
Make sure the machine is unplugged from the charger and check the status light.
Apologies. We can't help you online.
But our Customer Support Team will be able to solve your problem. Call us on 1-877-397-6622
Apologies. We can’t help you online.
But our Customer Support Team will be able to solve your problem.
Call us on 1-877-397-6622
The run time on High power is 7 minutes with the Motorised head, and 5 minutes without the Motorised head.
The run time on Medium power is 20 minutes with the Motorised head and 30 minutes without the Motorised head.
The run time on Low power is 35 minutes with the Motorised head and 60 minutes without the Motorised head.
Apologies. We can’t help you online.
But our Customer Support Team will be able to solve your problem.
Call us on 1-877-397-6622
Apologies. We can't help you online.
But our Customer Support Team will be able to solve your problem. Call us on 1-877-397-6622
A damp or musty smell is caused when dust in the cyclone has come into contact with water.
It may not be a direct contact with water, for example when vacuuming pet hair that is slightly damp, this moisture will combine with the dust in the cyclone causing the smell.
Additionally the smell may occur if the filter goes back into the machine wet.
Only the filter can be washed, the bin can be cleaned with a damp cloth only, and both must be completely dry before being refitted to the machine.
Under normal use, any unpleasant smell can only be caused by something the machine has picked up. Please select pick up issues to carry out checks.
If you are able to locate the smell to a part of the machine, replacing the part may help eliminate the smell. For this, please select Part broken.
The blockage light usually appears when the machine is pulsating. The blockage light is located by the power pack.
Push the bin release catch underneath the bin to release the base. Press the button located on the bin runner to release the bin and slide it off the runner.
Clean the clear bin with a damp cloth only.
WARNING: Do not use detergents, polishes or air fresheners to clean the clear bin. Do not put the clear bin in a dishwasher.
Ensure the clear bin is completely dry before replacing.
To replace the bin, push the bin up and in to the Main body of the machine, It will click into place.
Close the bin base so it clicks into place and is secure.
Washing the filter can also help to remove the smell.
This indicates the filter needs washing. Please follow the steps in the video.
Ensure the filter is completely dry before refitting. Press the trigger and run the machine for 2 minutes and then check the filter light.
Under normal use, any unpleasant smell can only be caused by something the machine has picked up. Please select pick up issues to carry out checks.
If you are able to locate the smell to a part of the machine, replacing the part may help eliminate the smell. For this, please select Part broken.
Remove the filter by twisting anticlockwise to the open position and gently pull away. Remove any excess debris from the filter prior to washing.
Wash the inside of the filter first; hold it upright under the cold tap and agitate using a rotation motion.
Wash the outside of the filter; fill it with cold water, place your hand over the open end and shake gently.
Repeat washing the inside and outside of the filter until the water runs clear.
Gently tap the filter to remove any excess water.
Leave the filter to dry with the open end facing up for as long as possible.
Ensure the filter is completely touch dry prior to refitting.
WARNING: Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave, or near a naked flame.
To refit, return the filter to the open position and twist clockwise until it clicks into place.
Please connect the floor tool directly on to the bin.
If the Brush bar on every tool spins when connected to the bin, please select the Wand is damaged.
Apologies. We can't help you online.
But our Customer Support Team will be able to solve your problem. Call us on 1-877-397-6622
On the side of the Direct drive cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.
Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.
Place the Cleaner head onto the bin and test the machine.
On the side of the Mini motorised head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.
Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.
Place the Cleaner head onto the bin and test the machine.
Under the Cleaner head by the Soft roller, locate the fastener. Using a coin, turn the fastener anticlockwise a quarter of the way to unlock the end cap, and slide it up to remove.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.
Place the Cleaner head onto the bin and test the machine.
Apologies. We can’t help you online.
But our Customer Support Team will be able to solve your problem.
Call us on 1-877-397-6622
Apologies. We can't help you online.
But our Customer Support Team will be able to solve your problem. Call us on 1-877-397-6622
Marks on the Wand can be caused when it has come into contact with a painted surface such as a door frame.
These can be removed by wiping with a damp cloth.
Apologies. We can’t help you online.
But our Customer Support Team will be able to solve your problem.
Call us on 1-877-397-6622
Please note that wall fixings are not included with the Dock.
Feed the charger cable through the rear of the dock, ensuring it is held via the retainer clip.
When securing the Dock to the wall, ensure there is a distance of 120cm from the floor. This is to allow the machine to sit in the dock without touching the floor.
The serial number can be found underneath the machine on the battery.
Please follow the steps in the video.
All the tools provided with the machine fit directly to the Wand or the bin inlet.
Click the tools to the end of the Wand assembly, ensuring the connections line up.
Remove the Wand. Place the tools directly onto the bin inlet until they click.
On the side of the Cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.
Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.
Remove the Brush bar from the Cleaner head and clear away any hair or fibres.
Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.
With the Brush bar clear from any debris, refit the Brush bar back into the cleaner head and securely fasten the end cap.
Place the Cleaner head onto the Wand and test the machine.
With the floor tool removed from the machine, turn over and undo the fastener.
Rotate the end cap to unlock and remove.
Remove the Brush bar and clear away any hair or debris.
Check the openings for any blockages, remove as necessary and replace the Brush bar.
Use a coin to lock the fastener.
Reassemble and test the machine.
Turn the cleaner head upside down so the underside of the cleaner head is facing you.
Rotate the end cap to the open position.
WARNING: Beware of sharp objects when checking for blockages.
Rotate the end cap to unlock and remove.
Gently slide the large Brush bar away from the Cleaner head and remove the end cap from the Brush bar.
Lift the smaller Brush bar up to remove.
Wash both the large and small Brush bar until the water runs clear.
Stand both Brush bars upright, leave to dry completely for a minimum of 24 hours.
Refit the small Brush bar first by inserting the round end of the small Brush bar into place. Push down the octagonal end until it clicks into place.
Reattach the end cap to the large Brush bar.
Slide the large Brush bar back onto the Cleaner head around the motor. Once in place rotate the end cap back into the closed position.
Close the fastener by turning a quarter turn clockwise. Ensure that the fastener is fully turned and that both the base plate and Brush bar is secure.
The machine can be charged on the dock or by plugging the charger directly to the machine.
The light on the charger will show when the machine is being charged and will go out when charging is complete.
The battery should be fully charged after 3.5 hours.
Please follow the steps in the video to empty the clear bin.
Empty as soon as the dirt reaches the level of the MAX mark - do not overfill. Ensure the machine is disconnected from the charger before emptying the clear bin. Be careful not to pull the 'ON' trigger.
Remove the Wand by pressing the red Wand release button and pulling away from the bin.
To release the dirt:
Hold the appliance with the bin in a downwards position.
Firmly push the red bin release button.
The bin will slide down, cleaning the shroud as it goes.
The bin base will then open.
The bin base will not open if the red button is not pushed down fully.
WARNING: Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave, or near a naked flame.
Please follow the steps in the video.
Ensure the filter is completely dry before refitting.
Remove the filter by twisting anticlockwise to the open position and gently pull away. Remove any excess debris from the filter prior to washing.
Wash the inside of the filter first; hold it upright under the cold tap and agitate using a rotation motion.
Wash the outside of the filter; fill it with cold water, place your hand over the open end and shake gently.
Repeat washing the inside and outside of the filter until the water runs clear.
Gently tap the filter to remove any excess water.
Leave the filter to dry with the open end facing up for as long as possible.
Ensure the filter is completely touch dry prior to refitting.
To refit, return the filter to the open position and twist clockwise until it clicks into place.
Dyson Cyclone V10 Total Clean - Costco Exclusive
Talking to us is easy